Products and Services for Embedded Computing

 Adapters/Carriers

   We have a new website. Please go to the new Adapters & Carriers

              page for the most up to date information:

         http://www.acttechnico.com/new_site/adapters_carriers.htm

ACT/Technico's Adapters allow you to use the wide variety of existing standard and custom PMC modules in your CompactPCI system. Both versions only use one slot in a system. The 3U adapter will accept a single PMC, where the 6U will hold two PMCs as well as mass storage devices.

6U VME64 / VMW64x PMC and PrPMC Carrier Board

i4400

  • Conduction cooling (optional)
  • VMEbus to PCI interface implemented in FPGA
  • Selectable standard VMEbus addressing (A24) with byte
  • (Even/odd) or word data transfers (D08(E/O)/D16/D32)
  • Features 2 single or 1 double PMC
  • 33 MHz/32-bit PCI interface to PMC modules
  • 3.3V PCI signaling on PMCs
  • Support for two ANSI/VITA 32-2003 compliant Processor PMCs
  • Rear I/O on P2 or optional P0 connector
  • Available in 3-row and 5-row VME with optional P0
  • Software selectable interrupt level per module
  • Thermal sensor for each PMC site
  • Voltage monitoring and front panel status display
     

2eSST VMEbus Carrier for PrPMC and PMC Modules

5000

  • Provides a high performance VMEbus interface for two PMC/XMC slots with an increasing of 4x the usable bus bandwidth compared with existing solution
  • Standards supported with the VMEbus interface :
    • Backward compatible with legacy protocols to preserve the existing VME system
    • VME64x extensions
    • 2eVME and 2eSST protocols
  • Full VMEbus system controller
  • Interrupt and Interrupt handling capability
  • PMC site one:
    • PrPMC or PMC 32/64-bit with PCI 33/66MHz or PCI-X 50/100Mhz
    • Compliant with IEEE1386.1
    • XMC support via 8-bit parallel RapidIO to the second PMC slot
    • VME interface via PCI-X 64-bit bus
  • PMC site two:
    • PMC 32-bit 33/66MHz or PCI-X up to 100Mhz
    • Compliant with IEEE1386.1
    • XMC support via RapidIO bus between the two PMCs
  • Cyclone FPGA to implement easily specific or customer functions
  • LED and Thermal sensor
  • 6U-form factor for use in VME or stand-alone systems
     

3U PMC to CompactPCI Adapter

7000

  • 3U CompactPCI Form Factor (100mm high x 160mm deep)
  • Only one slot (3U x 4HP) required
  • Passive Series Termination
  • For use with 32-bit PMCs
  • 64 User I/O lines routed to CPCI connector (models 7000-2 and 7000-4)
  • 2 Status LEDs: IRQ Request from PMC and PMC Bus Master
  • Accepts standard PMC I/O connector through the CPCI front panel
  • P/N 7000-1: for use in 64-bit systems; no rear I/O; J1 only
  • P/N 7000-2: for use in 32-bit systems; rear I/O; J2 connector
  • P/N 7000-3: same as -1, mounted at bottom of 6U Front Panel
  • P/N 7000-4: same as -2, mounted at bottom of 6U Front Panel
  • Hot Swap version also available - contact sales
     





6U PMC to CompactPCI Carrier  

7040

  • 6U CompactPCI Form Factor (233.4mm high x 160mm deep)
  • Only one slot (6U x 4HP) required
  • Two PMC sites accept standard PMC modules through the front panel
  • Optional Transition Module supports rear I/O
  • Compliant with PICMG 2.1 Hot Swap specification
  • Compatible with many cPCI High Availability (HA) platforms
  • DEC 21154 PCI bridge chip

     



Click here to see other PMC Adapter [Carrier]