|
Adapters |
|
- Meets PCI Mezzanine Card (PMC) IEEE 1386 specification
- Compatible with Motorola PowerPC SBCs and others with PMC sites
- Off-the-shelf PMC modules fit a wide variety of applications
- Reduce development costs of implementing PMC technology
- When used with ACT/Technico's CompactPCI-PMC Adapter (7000 series), functionality can be added without concern
for form factor compatibility
- Custom designs are readily available
- Devices drivers available: VxWorks, LynxOS, Solaris, Linux, and Windows
|
|
|
2eSST VME to PMC/PMC-X |
|
2eSST VMEbus Carrier for PrPMC and PMC Modules |
5000 |
- Provides a high performance VMEbus interface for two PMC/XMC slots with an increasing of 4x the usable bus bandwidth
compared with existing solution
- Standards supported with the VMEbus interface :
- Backward compatible with legacy protocols to preserve the existing VME system
- VME64x extensions
- 2eVME and 2eSST protocols
- Full VMEbus system controller
- Interrupt and Interrupt handling capability
- PMC site one:
- PrPMC or PMC 32/64-bit with PCI 33/66MHz or PCI-X 50/100Mhz
- Compliant with IEEE1386.1
- XMC support via 8-bit parallel RapidIO to the second PMC slot
- VME interface via PCI-X 64-bit bus
- PMC site two:
- PMC 32-bit 33/66MHz or PCI-X up to 100Mhz
- Compliant with IEEE1386.1
- XMC support via RapidIO bus between the two PMCs
- Cyclone FPGA to implement easily specific or customer functions
- LED and Thermal sensor
- 6U-form factor for use in VME or stand-alone systems
|
|
|
PCI to PMC |
|
PCI to PMC Adapter for Test |
8097 |
- For use in a lab environment
- Enables use of 32‑bit PCI card in a PMC slot
- PCI card plugs in perpendicular to PMC card
- Connector permits short PCI card to plug in without interfering with a
- VME backplane or board front panel
- LEDs monitor power supplies and key PCI signals
- Two versions: 5V and 3.3V
|
|
|
PCI-x to PMC-x |
|
32/64b 33/66 MHz PCI-x to PMC-x Adapter |
8098 |
- Permits operation of a standard 32 or 64 bit PCI-X card in a PMC slot
- Passive adapter - no software set up required
- Supports "PCI-X Capable" signal allowing use of legacy PCI boards or PCI-X boards
- LEDs monitor power supplies and key signals from the PCI bus
|
 
|
|
32/64b 33/66 MHz PCI-x to PMC-x Adapter |
8098a |
- Permits operation of a standard 32 or 64 bit PCI-X card in a PMC slot
- Passive adapter - no software set up required
- Supports "PCI-X Capable" signal allowing use of legacy PCI boards or PCI-X boards
- LEDs monitor power supplies and key signals from the PCI bus
- 10 Watt 5V to 3.3V DC to DC converter
|
|
|
|
|
|
PCMCIA to PMC |
|
PCMCIA to PMC Adapter |
8073 |
- Permits use of a Type I or Type II PCMCIA card in PMC slot
|
|
|
|
|
|
PMC to CompactPCI |
|
3U PMC to CompactPCI Adapter |
7000 |
- 3U CompactPCI Form Factor (100mm high x 160mm deep)
- Only one slot (3U x 4HP) required
- Passive Series Termination
- For use with 32-bit PMCs
- 64 User I/O lines routed to CPCI connector (models 7000-2 and 7000-4)
- 2 Status LEDs: IRQ Request from PMC and PMC Bus Master
- Accepts standard PMC I/O connector through the CPCI front panel
- P/N 7000-1: for use in 64-bit systems; no rear I/O; J1 only
- P/N 7000-2: for use in 32-bit systems; rear I/O; J2 connector
- P/N 7000-3: same as -1, mounted at bottom of 6U Front Panel
- P/N 7000-4: same as -2, mounted at bottom of 6U Front Panel
- Hot Swap version also available - contact sales
|
|
|
6U PMC to CompactPCI Carrier |
7040 |
- 6U CompactPCI Form Factor (233.4mm high x 160mm deep)
- Only one slot (6U x 4HP) required
- Two PMC sites accept standard PMC modules through the front panel
- Optional Transition Module supports rear I/O
- Compliant with PICMG 2.1 Hot Swap specification
- Compatible with many cPCI High Availability (HA) platforms
- DEC 21154 PCI bridge chip
|
|
|
|
|
|
PMC to PCI |
|
PMC to PCI Adapter for Test |
8091 |
- Allows operation of standard 32-bit PCI card in a PMC slot
|
|
|
Bridged 64-bit/66 MHz PMC to PCI Adapter |
8093 |
- Enables use of PMC within a PCI environment
- 21154 PCI to PCI bridge chip operates in either 33 or 66 Mhz
- Utilizes 3.3V power directly from the PCI
- LEDs monitor power, voltage and key bus signals
- JTAG signals brought out to 10-pin headers to program PLD and FPGA logic on PMC
- Rows A & C connect with 64-pin connector on PMC for rear I/O
- Optional fan assembly (P/N 8094F) provides cooling for PMCs with high power output
|
|
|
Bridged 64-bit/66 MHz DC/DC PMC to PCI Adapter |
8094 |
- Enables use of PMC within a PCI environment
- 21154 PCI to PCI bridge chip operates in either 33 or 66 Mhz
- Provides DC to DC converter to convert 5V power from PCI to 3.3V on PMC
- LEDs monitor power, voltage and key bus signals
- JTAG signals brought out to 10-pin headers to program PLD and FPGA logic on PMC
- Rows A & C connect with 64-pin connector on PMC for rear I/O
- Optional fan assembly (P/N 8094F) provides cooling for PMCs with high power output
|
|
|
Optional fan assembly |
8094F |
- Provides cooling for PMCs with high power output
- Optional fan assembly for 8093 and 8094
|
|
|
PMC to PCI Adapter for Delivery |
|
32-bit PMC to PCI Adapter for Delivery |
8092 |
- Enables the use of PMCs in a PCI based system
- Designed as a low cost solution
- A & C rows of 96-pin DIN connect with 64-pin I/O connector
- Includes aluminum front panel
|
|
|
|
|
|
64-bit PMC to PCI Adapter for Delivery |
8096 |
- Enables the use of PMCs in a PCI based system
- Designed to improve signal integrity while retaining passive adapter
- Key control signals on PCI fixed to ground to reduce signal undershoot
- 5V to 3.3V Linear regulator provided
- LEDs monitor power and key PCI signals
- VIO signal monitor LED to determine 3.3V or 5V bus signaling
- Cooling fan provided for higher power PMCs
- A & C rows of 96-pin DIN connect with 64-pin I/O connector
|
|
|
|
|
|
PMC-x to PCI-x |
|
Bridged PMC-X to PCI-X Adapter with Optional Fan Assembly |
8099 |
- Permits delivery of PMC derived applications in a standard PCI or PCI-X environment
- Supports PMC (IEEE 1386) and PMC-X (VITA 39)
- Intel 31154 bridge operates at 33/66MHz (PCI) or 66/100/133MHz PCI-X
- LEDs monitor power supplies and key signals from the PCI bus
- Optional Fan Assembly Part # 8094F
- Selectable 3.3V or 5V PCI bus signaling levels
|
|
|
PMC to PMC |
|
64 bit, 66 MHz Metering PMC to PMC Extender |
8100 |
- For development use with PMCs on a VMEbus, CompactPCI or other board
- Enables user access to Side 1 of the exposed PMC for probing
- Supports 3.3V and 5V PCI signaling
- Works with 33 MHz and 66 MHz clock speeds and 32‑bit or 66‑bit bus
- widths
- Current sensing and self‑resetting fuse protected power for +5V,
- +3.3V, +12V and ‑12V
- Altera PLD displays voltage value and/or bus/bandwidth via 4‑digit LED
- Activity LEDs provide display of PCI bus activity, power supply
- tolerance and selected metering modes
- Designed to support Processor PMC use
|
|
